Search Results

More stringent emissions regulations, fuel economy standards, and regulations are currently being discussed to help reduce both CO2 and exhaust emissions. Vehicle manufacturers have been developing new engine technologies, such as downsizing and down-speeding with reduced friction loss, improved engine combustion and efficiency, heat loss recycling, power-train friction loss recycling, and reduced power-train friction loss. The use of more efficient fuel economy 5W-30 engine oils for heavy duty commercial vehicles has started to expand since 2009 in Japan as one technological solution to help reduce CO2 emissions. However, fuel economy 5W-30 oils for use in heavy duty vehicles in Europe are mainly based on synthetic oils, which are much expensive than the mineral oils that are predominantly used in Japan.

An energy management method and model for small electric buses was studied. The model consists of a drive motor & inverter, a lithium ion battery, electric auxiliary devices and a mechanical powertrain. A small electric bus was developed based on the short travel distance, high charging frequency concept. Since 2012, two buses have operated as community buses in two different regions, and another bus started operations in a third region in 2013. The development of an energy management model accounting for operating conditions made it possible to keep the lithium ion battery capacity to a minimum. This paper describes energy management for this small electric bus, the design of the vehicle and the results of evaluating actual operation.

The U.S. Environmental Protection Agency (EPA) issued new emissions regulations, which came into effect in January, 2010. These EPA 2010 regulations are the most stringent emissions standards in the world, reducing both particulate matter (PM) and nitrogen oxides (NOx) to nearly zero levels. Hino Motors improved upon its previous EPA 2007-compliant engine, developing a new exhaust after-treatment system in which a Diesel Particulate active Reduction System (DPR), a Urea-Selective Catalytic Reduction (SCR) System and a Burner System are employed to meet EPA 2010 emissions regulations for medium duty commercial vehicles. DPR was already developed and utilized to reduce PM to meet EPA 2007 standards, but the Urea-SCR System is newly developed technology used to reduce NOx emissions to comply with EPA2010 emissions regulations. In addition, a Burner System is used to elevate exhaust gas temperatures in order to improve both SCR performance and DPR active Regeneration.

Diesel particulate trap systems are one of the effective means for the control of particulate emission from diesel vehicles. Hino has been researching and developing various diesel particulate trap systems for city buses. This paper describes two of the systems. One uses a wall flow filter equipped with an electric heater and a sensing device for particulate loading for the purpose of filter regeneration. Another makes use of a special filter named “Cross Flow Filter” with an epoch-making regeneration method called “Reverse Jet Cleaning”, by which it becomes possible to separate the part for particulate burning from the filter. Both systems roughly have come to satisfy the functions of trap systems for city buses, but their durability and reliability for city buses are not yet sufficient.

Historically the high speed diesel engine for commercial vehicles has been developed along with its combustion system in compliance with political and economical changes. After the 1970's, stricter exhaust emission regulations and fuel economy requirements induced combustion developments and application of turbocharged and inter cooled engines. From the late 1980's, high pressure fuel injection has been investigated and recognized as an essential tool for lowering emissions especially of particulate matter. Although turbulence effects on both in-cylinder air motion and during the combustion process are quite effective, they show different phenomena in conventional and advanced high pressure fuel injection systems. In the 1990's, multiple injection with high pressure has been attempted for further reduction of NOx and particulate matter.

Diesel Particulate active Reduction system (DPR) is a system that traps particulate matter in diesel exhaust gas with a particulate filter and actively regenerates the filter when PM accumulates to a specific level. In 2003, DPR was installed on Hino's light-, medium-, and heavy-duty diesel engines, and about 50,000 units of these DPR-equipped diesel engines are currently on the market. This paper reports results of further progress made on optimization of the active regeneration function of DPR. The goal of successful development of DPR is to optimally control the system under various engine-operating conditions to regenerate the filter without producing abnormal combustion of PM and to minimize the amount of unburned PM to keep the filter from clogging. To improve the control of DPR, the combustion phenomena of PM collecting on the filter were studied through visualization, and the factors influencing combustion were determined.

DPR is a particulate-emissions reduction system that has been developed to reduce particulate emissions in production commercial vehicles and consists of a multiple fuel-injection system, an engine electronic control unit, and a DPR-Cleaner which includes an oxidation catalyst, a catalyzed particulate filter, and silencers. DPR performs active regeneration to accelerate the regeneration of the filter under engine operating conditions where regeneration by passive regeneration alone is not sufficient. Thus, DPR makes it possible to regenerate the filter regardless of the exhaust gas temperature and enables significant reduction of particulate in commercial vehicles to levels below 0.027 g/kWh under Japan's D13 mode operating conditions. The authors describe development results of the DPR.

In this study, a scheme for controlling the deceleration rate required to alleviate shockwave propagation in a vehicle platoon is proposed. Assuming a three-vehicle platoon, the deceleration rates of the 2nd and the 3rd vehicles were modeled so as to minimize the speed of the shockwave that propagates through the platoon. The effect of the decelerating two vehicles on a 4th following vehicle was also evaluated. Numerical analysis showed that an earlier and slightly more rapid deceleration rate significantly decreased the speed of the shockwave propagated by the first three vehicles. Furthermore, even though the shockwave was amplified through the 2nd to 4th vehicles, this negative effect could be eliminated by applying the same control strategy to the 3rd and 4th vehicles.

This paper describes the combustion optimizations of heavy-duty diesel engines for the anticipated future emissions regulations by means of an electronically controlled common rail injection system. Tests were conducted on a turbocharged and aftercooled (TCA) prototype heavy-duty diesel engine. To improve both NOx-fuel consumption and NOx-PM trade-offs, fuel injection characteristics including injection timing, injection pressure, pilot injection quantity, and injection interval on emissions and engine performances were explored. Then intake swirl ratio and combustion chamber geometry were modified to optimize air-fuel mixing and to emphasize the pilot injection effects. Finally, for further NOx reductions, the potentials of the combined use of EGR and pilot injection were experimentally examined. The results showed that the NOx-fuel consumption trade-off is improved by an optimum swirl ratio and combustion chamber geometry as well as by a new pilot concept.

Urea selective catalyst reduction (SCR) systems have a high NOx conversion rate because the ammonia formed by the hydrolyzing urea solution reacts with NOx efficiently as a reducing agent. Systems combining urea-SCR and a diesel particulate filter (DPF) have been adopted in heavy duty vehicles to meet the post new long term emissions regulations in Japan. This study examined the emissions reduction performance of these systems after 160,000 km. The emissions that were examined included both regulated emissions (NOx, PM, HC, and CO) and unregulated emissions. As a result, the cleanness of diesel emissions from a urea-SCR and DPF system was confirmed.

Diesel Particulate Filter (DPF) is a very effective aftertreatment device to limit particulate emissions from diesel engines. As the amount of soot collected in the DPF increases, the pressure loss increases. Therefore, DPF regeneration needs to be performed. Injected fuel into the exhaust line upstream of the Diesel Oxidation Catalyst (DOC), hydrocarbons are oxidized on the DOC, which increases the exhaust gas temperature at the DPF inlet. It is also necessary that the injected fuel is completely vaporized before entering the DOC, and uniformly mixed with the exhaust gases in order to make the DOC work efficiency. However, ensuring complete evaporation and an optimum mixture distribution in the exhaust line are challenging. Therefore, it is important that the fuel spray feature is grasped to perform DPF regeneration effectively. The purpose of this study is the constructing a simulation model.

Approximately 200,000 units of Hino J-series diesel engine were produced for 7 years. The J-series engines had a reputation all over the world for their performance, reliability, lightweight, and installation ability. They are composed of 4, 6 cylinders engines and unique 5-cylinder engine J07C. In 2002, newly modified J-series engines, which met the Japan 2001 noise emission regulations, were developed and J07C-TI, 5-cylinder TI engine, equipped with a common-rail fuel injection system was added in the J-series. Common-rail fuel injection system was equipped in order to achieve the emission targets in the future as well as to meet the current emission regulations. Achieving higher injection pressure level through the all engine speed, include excess low speed, was effective in reduction of PM emissions and in increasing of low engine speed torque drastically.

The urea-SCR system is one of the most promising aftertreatment systems for future automotive diesel engines. We developed a urea dosing device with twin urea injectors for onboard applications, to enhance the NOx reduction performance at low exhaust temperatures and to lower the electric power consumption of the SCR system. The injectors operate with a single-phase urea solution, without air assist. Of the injectors, one is used to supply urea to a bypass passage routing the exhaust, during low exhaust temperatures. The other injector is located on the wall of the main exhaust duct, directly supplying urea to the exhaust. This direct injection method has a uniform spray distribution problem. A set of impact plates were used to distribute the spray. Impact plates have a high potential for deposition, but use of film boiling was considered. A thermal analysis was conducted and as a result, deposit conditions were theoretically derived. This was confirmed through experiments.

In order to reduce diesel NOx emissions, aftertreatment methods including LNT (Lean NOx Trap) and urea SCR (Selective Catalytic Reduction) have been researched. One of the shortcomings of urea SCR is its NOx reduction performance degradation at low exhaust gas temperatures and possible emission of unregulated byproducts. Here, a new type of a urea-dosing device to overcome these shortcomings is studied. This dosing device actively produces ammonia without depending upon the exhaust gas temperature, and designed for onboard application. The device incorporates an electrically heated bypass with a hydrolysis catalyst. An injector supplies urea solution into the bypass. The bypass is heated only when thermolysis is needed to produce ammonia (NH3). The hydrolysis catalyst further assists in the production of NH3. The ammonia gas obtained is then mixed with the main exhaust gas flow.